We've found this post pertaining to Tools You Need to Install a New Bathtub down the page on the web and think it made good sense to relate it with you in this article.
Installing a bath tub isn't precisely rocket science, but it does call for solid plumbing, woodworking, and also often, tiling skills. Changing an old bathtub with a brand-new one is likewise a moderately hard task. If the old bathtub is conveniently easily accessible, the job can move quickly; if you need to open up a wall surface to eliminate the old bathtub and place the brand-new bathtub, the task is a lot harder. In either situation, the project is within a house handyman's abilities, although you will need a helper to leave the old bathtub as well as set in the new one. Ensure you have actually certified on your own for the task as well as are comfortable attempting it. Instead of working with a professional to take over a halfway-completed project, it is far better to think about employing one before you start. Possibilities are you might need an expert plumber to make tube links.
This article will aid you mount a brand-new bathtub in your shower room if you have already acquired a new tub as well as don't require to change the setup of your previous water system pipelines.
Your tools and also product checklist should make up the following:
Removing Old Touches
If you need to replace old faucets with brand-new ones as a part of your installment, then the first thing you should do is detach the water supply. After doing so, switch on the taps to drain any kind of water continuing to be in the system. The process of getting rid of the existing taps can be rather bothersome because of the restricted accessibility that is typically the case.
Utilize a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that links the supply pipelines to the taps. Have a cloth all set for the staying water that will certainly originate from the pipes. Once the supply pipelines have actually been removed, utilize the very same device to loosen the nut that holds the taps onto the bath/basin. You will require to quit the solitary taps from transforming during this procedure. As soon as the taps have actually been removed, the holes in the bath/basin will need to be cleaned up of any kind of old sealing compound.
Before carrying on to fit the new faucets, contrast the pipe connections on the old faucets to the new faucets. If the old faucets are longer than the brand-new taps, after that a shank adapter is required for the brand-new taps to fit.
Suitable New Taps
If the tails of the new faucets are plastic, after that you will need a plastic connector to stop damages to the thread. One end of the adapter fits on the plastic tail of the faucet and also the other end supplies a connection to the existent supply pipelines.
If you require to fit a monobloc, then you will certainly require decreasing couplers, which attaches the 10mm pipeline of the monobloc to the typical 15mm supply pipe.
Next, place the faucet in the placing opening in the bath/basin guaranteeing that the washers are in place in between the tap and the sink. Secure the tap in position with the producer given backnut. Once the faucet is securely in position, the supply pipelines can be attached to the tails of the faucets. The faucets can either be attached by utilizing corrugated copper piping or with typical tap connectors. The former type should be connected to the faucet ends initially, tightening only by hand. The supply pipes can later on be attached to the other end. Tighten up both ends with a spanner after both ends have actually been linked.
Mounting the Bathtub
Utilizing both wood boards under its feet, put the bath tub in the needed position. The wood boards are helpful in uniformly spreading the weight of the bath tub over the area of the boards rather than concentrating all the weight onto four tiny points.
The next objective is to make certain that the bath tub is leveled all round. This can be accomplished by checking the level as well as readjusting the feet on the tub until the spirit level reviews degree.
To set up taps, fit the bottom of the furthest adaptable faucet connector to the proper supply pipe by making a compression sign up with; then do the very same for the other tap.
Switch on the water system and also check all joints and also new pipework for leaks as well as tighten them if essential. Fill the bathtub and also examine the overflow outlet and the normal electrical outlet for leaks.
Lastly, repair the bathroom paneling as defined in the maker's user's manual. Tiling as well as securing around the bathtub should wait up until the bathtub has been made use of a minimum of once as this will certainly resolve it into its last position.
Planning for the Setup
Firstly, the sustaining framework supplied with the bath should be fitted (if called for) according to the manufacturer's instructions. Next, fit the faucets or mixer to the bathtub. When suitable the tap block, it is essential to make sure that if the faucet includes a plastic washer, it is fitted between the bath and the faucets. On a plastic bath, it is additionally sensible to fit a sustaining plate under the faucets unit to prevent strain on the bathtub.
Fit the adaptable faucet adapters to the bottom of both faucets using 2 nuts and also olives (often provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet through the hole in the bathroom. Make use of the nut supplied by the supplier to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the versatile overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bath. Make certain you utilize every one of the provided washers.
Attach the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Attach all-time low of the overflow tube in a similar manner.The bathroom ought to now prepare to be fitted in its last setting.
Tiling Around the Bathtub
In the area where the bath satisfies the tile, it is needed to secure the joins with a silicone rubber caulking. This is very important as the fitting can move enough to break an inflexible seal, creating the water to pass through the wall in between the bath as well as the tiling, causing problems with dampness and also feasible leakages to the ceiling listed below.
You can choose from a range of coloured sealants to assimilate your components as well as fittings. They are marketed in tubes and also cartridges, and also can sealing voids up to a width of 3mm (1/8 inch). If you have a bigger void to fill, you can load it with spins of soaked newspaper or soft rope. Keep in mind to constantly fill the tub with water before sealing, to permit the movement experienced when the tub remains in usage. The sealer can break rather early if you do not take into consideration this motion prior to securing.
Conversely, ceramic coving or quadrant ceramic tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are additionally quickly readily available on the market. It is advisable to fit the floor tiles using waterproof or waterproof sticky and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Hopefully you enjoyed our post about Tools You Need to Install a New Bathtub . Thanks so much for taking the time to read through our blog post. Appreciated our blog? Please share it. Help other people find it. Thanks a lot for your time. Kindly check our site back soon.
Overflow? We can help!